亚洲色偷偷综合亚洲AV伊人蜜桃_最近免费看av_国产人妻午夜在线无码_国语FREE性XXXXXHD_高清做爰免费无遮网站挡_国产精品呻吟AV久久高潮

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tilting furnace hydraulic cylinder Sold to Malaysia

Release time:2023-11-14 08:41:11 Hits: Current position: Home > News

This article mainly introduces:

Malaysia hydraulic cylinder,tilting furnace hydraulic cylinder manufacturer,tilting furnace hydraulic cylinder

Malaysia tilting furnace hydraulic cylinder

(Malaysia tilting furnace hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

tilting furnace hydraulic cylinder are widely used in Malaysia,because of long service life,smooth movement,high work efficiency.So our company has designed tilting furnace hydraulic cylinder for customers from Malaysia.

Introduction to tilting furnace hydraulic cylinder:

When the tilting furnace hydraulic cylinder is installed on the main engine, the oil port piping part and the guide sleeve should be checked for oil leakage in the running test, and the earring and the middle hinge shaft bearing should be refueled.

When the tilting furnace hydraulic cylinder is repaired, its inner and outer diameter and roundness should be accurately measured. If the inner hole of the tilting furnace hydraulic cylinder is badly worn, it can be repaired by grinding the mandrel or honing on the boring machine. If the piston is worn, it can be repaired by electroplating, and serious wear should be replaced.

The tilting furnace hydraulic cylinder is not the same as the tilting furnace hydraulic cylinder, because the pressure of the pneumatic system is generally within the range of 0.2-1.0Mpa, the tilting furnace hydraulic cylinder can not be used as a high-power power component, but the tilting furnace hydraulic cylinder can be used as a relatively large power component, or the tilting furnace hydraulic cylinder system can be used.

The repair method of the tilting furnace hydraulic cylinder: the repair of the tilting furnace hydraulic cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.

Answers to some questions about tilting furnace hydraulic cylinder:

How is the cylinder of hydraulic cylinder processed?
As the main parts of hydraulic cylinder, mining single pillar, hydraulic support, gun barrel and other products, its processing quality directly affects the life and reliability of the whole product. Cylinder processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of cylinder is deep hole processing, which has always troubled the processing personnel. Due to the residual compressive stress on the surface of the surface layer, the rolling machining is helpful to seal the small cracks on the surface and prevent the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the cylinder can be improved.

What should we pay attention to when using the cylinder?
When using the cylinder, we should pay attention to the environment and temperature in which it is located as follows: 1. Before working, the hydraulic cylinder must carry out several reciprocating movements under low pressure (greater than the starting pressure), and work normally after removing the gas in the cylinder. 2. Precautions when removing the hydraulic cylinder: ① The pressure in the hydraulic circuit is reduced to zero before disassembly. ② The screw thread at the top of the piston rod should be prevented from damage when disassembling. ③ Due to the different structure and size of the hydraulic cylinder, the order of disassembly is also slightly different. Generally, the fastening bolt of the end cover should be loosened first. Internal card chain card key application special tools.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
主站蜘蛛池模板: 免费A级毛片无码A∨中文字幕 | 免费A片国产毛无码A片牛牛 | 精品国产一区二区三区四区五区 | 成年入口无限观看免费完整大片 | 亚洲AV之男人的天堂网站 | 波多野结衣在线播放一区 | 奇米影视888欧美在线观看 | 欧洲熟妇色XXXXX欧美 | 99国产精品热久久久久久 | 五月天综合网缴情五月中文 | 久久五月丁香中文字幕 | 久久久伦理 | 毛片大全真人在线 | 男女18禁啪啪无遮挡激烈 | 日本岛国片在线观看一区二区 | 天堂亚洲免费视频 | 奶头好大下面好爽的视频 | 免费观看国产美女裸体视频 | 日本久久综合久久综合 | 久久国产乱子伦免费精品无码 | 久久久久久a女人 | 日韩免费一区二区三区高清 | 免费一级 国产 | 亚洲熟妇无码AV在线观看网址 | 日日碰狠狠添天天爽五月婷 | 综艺向的生活第六季免费观看 | 国内精品久久久久久久影视 | 男人的天堂色 | 一级毛片网站免费看 | 亚洲精品尤物av在线观看任我爽 | 小箩莉h文徐韵婷合集小说 免费的国产成人AV网站 | 2018天天拍拍天天爽视频 | 玩弄人妻少妇精品视频 | 免费A片国产毛无码A片牛牛 | 国产福利一区二区精品秒拍 | 亚洲精品无码成人A片蜜臀 无码国产69精品久久久久孕妇 | 特级毛片A级毛片免费观看网站 | 中国人妻被两个老外三p | 成人无码区免费A片视频韩国 | 国产AV国产精品白丝JK制服 | 无码AV久久久久久久久 |